Arduino
You can connect Arduino or similar boards to Universal Controller to handle events from connected sensors or receive commands for locally connected relays, motors etc.
Receiving commands from EVA ICS
There’s no common way controlling embedded boards from EVA ICS. You may define any API inside a board, then just use external scripts or develop own PHI module to link Universal Controller and board.
Sending data to EVA ICS UC
It’s highly recommended to use UC UDP API to communicate with Universal Controller to avoid Arduino board freezing.
To enable UDP API, you must firstly configure udpapi/listen and udpapi/hosts-allow options in config/uc/main registry key (don’t forget to restart Universal Controller after configuration is modified).
Example. Consider there are 2 motion (PIR) sensors connected with Arduino board on pins #2 and #3, the board has Ethernet shield to send events via UDP protocol, there is also a signal LED connected to board pin #7.
On events, the board updates states of EVA ICS sensors sensor:security/motion1 and sensor:security/motion2. We’ll use plain (unencrypted) UDP API and Universal Controller will receive state updates without API key.
Setup EVA ICS UC
Create 2 sensors:
# create sensors
eva uc create sensor:security/motion1 -y
eva uc create sensor:security/motion2 -y
# enable sensors (set status to 1)
eva uc update sensor:security/motion1 -s1
eva uc update sensor:security/motion2 -s1
Sensors will get value “1” when motion is detected by PIR and “0” when motion is over.
Setup Arduino
#include <SPI.h>
#include <Ethernet.h>
#include <EthernetUdp.h>
// motion sensors pins
int mPin1 = 2;
int mPin2 = 3;
// motion sensor states
int mNow1 = 1;
int mNow2 = 1;
// previous motion sensor states
int mOld1 = 0;
int mOld2 = 0;
// signal LED pin
int lPin = 7;
int toLedSeconds = 0;
// EVA ICS UC IP
IPAddress aSrvIP(192, 168, 1, 11);
int aSrvPort = 8881;
byte mac[] = {
0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x01 };
EthernetUDP Udp;
void(* resetFunc) (void) = 0;
void setup() {
pinMode (mPin1,INPUT);
pinMode (mPin2, INPUT);
pinMode (lPin, OUTPUT);
Serial.begin(9600);
Serial.print("Waiting for sensor calibration...");
for (int i=10;i>0;i--) {
Serial.print(i,DEC);
Serial.print(" ");
digitalWrite(lPin,HIGH);
delay(500);
digitalWrite(lPin,LOW);
delay(500);
}
Serial.println();
Serial.println("Motion sensor calibration check...");
while ((mNow1+mNow2)!=0) {
updateSensors();
delay(10);
}
Serial.print("Configuring ethernet...");
if (Ethernet.begin(mac) == 0) {
Serial.println("Failed, restarting in 5 seconds");
for (int i=0;i<2;i++) {
digitalWrite(lPin,HIGH);
delay(500);
digitalWrite(lPin,LOW);
delay(500);
}
delay(3000);
resetFunc();
return;
}
for (byte thisByte = 0; thisByte < 4; thisByte++) {
// print the value of each byte of the IP address:
Serial.print(Ethernet.localIP()[thisByte], DEC);
Serial.print(".");
}
Serial.println();
Serial.println("Started");
// blink signal LED 3 times
Udp.begin(aSrvPort);
for (int i=0;i<3;i++) {
digitalWrite(lPin,HIGH);
delay(200);
digitalWrite(lPin,LOW);
delay(200);
}
}
void updateSensors() {
mNow1 = digitalRead(mPin1);
mNow2 = digitalRead(mPin2);
}
void sendNotify(char* sensor,int value) {
char p[100];
char v[10];
strcpy(p,sensor);
strcat(p," u None ");
itoa(value,v,10);
strcat(p,v);
strcat(p,0);
Udp.beginPacket(aSrvIP,aSrvPort);
Udp.write(p);
Udp.endPacket();
}
void loop() {
updateSensors();
if (mNow1!=mOld1) {
mOld1=mNow1;
Serial.print("Motion sensor 1 value change: ");
Serial.println(mNow1,DEC);
if (mNow1>0) toLedSeconds=3000;
sendNotify("sensor:security/motion1",mNow1);
}
if (mNow2!=mOld2) {
mOld2=mNow2;
Serial.print("Motion sensor 2 value change: ");
Serial.println(mNow2,DEC);
if (mNow2>0) toLedSeconds=3000;
sendNotify("sensor:security/motion2",mNow2);
}
if (toLedSeconds--==3000) digitalWrite(lPin,HIGH);
if (toLedSeconds==0) digitalWrite(lPin,LOW);
delay(1);
}